---
title: "Name"
url: "https://help.maxon.net/c4d/en-us/Content/html/NET_MAXON_NEUTRON_ASSET_OP_BARCHART-EDKSX8P3J1LHP7P_PCC2HL.html"
section_path: "The Node Editor > The individual Assets > Experimental > Bar Chart > Name"
element_id: "NET_MAXON_NEUTRON_ASSET_OP_BARCHART"
group_id: "EDKSX8P3J1LHP7P_PCC2HL"
description: "Here you activate the display of the respective names of the data on the bars."
---

## Name

### Labels

Parameter ID: `INPORT_J08MPFJFL9WPAFP4OYO_DP`

Here you activate the display of the respective names of the data on the bars.

### Placement

Parameter ID: `INPORT_YWT0HR42GX9RWOJGKV8S_O`

Use this menu to define where the names should be placed on the bars. You will find identical settings for the placement of the numerical values on the bars in the "Numbers" section of the settings:

- About: The designation is above the end of each bar.
- Under: The designation is under each bar. This corresponds to the preset mode.
- At the top: The label is displayed centered above each bar.
- Baseline: In this mode, the placement itself can be made via the **Baseline** value.

### Baseline

Parameter ID: `UKG5CS8KKRJVAWUPJIO4EC` · Range: [-∞..+∞]

In the "Baseline" **placement** mode, you can enter any displacement value here to freely place the label.

### Align

Parameter ID: `INPORT_QHCJOIDJOB0GDNIQWY_XZO`

This menu influences the alignment of the labels on the bars. The respective reference point is selected via the **placement**:

- Automatic: Alignment is automatic depending on the selected placement. For example, if labels are placed above the bars, they will then be right-aligned; if they are placed on the bars, they will be center-aligned; and if they are placed below the base of the bars, they will be left-aligned.
- Left: The labels are placed flush left.
- Center: The labels are placed in the center.
- Right: The labels are displayed right-justified.

### Offset.P

Parameter ID: `INPORT_KKDWJFNQMHXTBRBKJU89CU` · Range: [XYZ m]

### Offset.R

Parameter ID: `INPORT_FCT1GJQ3HFEGXHMGGGCYTT` · Range: [HBP °]

### Offset.S

Parameter ID: `INPORT_BJTNMEO2KTBJBX8EGGNGUT` · Range: [XYZ ]

With these vectors the labels can be additionally moved, rotated and scaled.

### Flip

Parameter ID: `MMZTDDI1GDOLSYCYTRLX8A`

Enabling this option will cause the designations to be read from the opposite side. This influences not only the reading direction, but also the placement of the labels.

### Font

Parameter ID: `INPORT_XIUYMV2FKLSTIF_RJMJ_9S`

This font is used for the labels on the bars.

### Size

Parameter ID: `INPORT_F5DME6KALHFJ_K_UZLMXEL` · Range: [-∞..+∞%]

This can be used to set the size of the texts on the bars.

### Extrusion

Parameter ID: `INPORT_A6SCEKXKA1QGTTC2OUZLWU` · Range: [-∞..+∞m]

The texts are also created as splines, which can then be extruded. Here you define the offset of the extrusion, i.e., the height of the extruded designations along the Y axis.

### Bevel

Parameter ID: `INPORT_MAZ29HQEEBRKA8IHVPUXDQ` · Range: [-∞..+∞%]

This value specifies the size of the cover rounding on the extruded designations.